Replacement Refrigerator Water Filter For:
PUR 4396841B
Filter Features
-
Filter Life: 6-Months
-
Filter Capacity: 200 Gallon
-
NSF Certified 42 & 53
-
Taste
-
Odor
-
Chlorine
-
Reduces 24 Contaminants Including Pharmaceuticals
-
Replacement Refrigerator Water Filter For:
4396841B
2-Pack ($35.99)
Save:
$34.00
158 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
4396841B
3-Pack ($52.99)
Save:
$47.00
237 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
4396841B
4-Pack ($69.99)
Save:
$60.00
95 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
4396841B
6-Pack ($102.99)
Save:
$27.00
69 Review
Add To Cart
Remove unhealthy contaminants and any haziness efficiently from your drinking water with pur 4396841b at Clatterans which uses the highest quality activated carbon and certifies to IAPMO, NSF/ANSI water treatment standards 42 for trapping and reducing detrimental impurities to reach the best water filtration results. We have numerous pur refrigerator filter replacements to fit perfectly in your fridge. Fitermodel is an acceptable substitute without compromise on quality and flow to provide wholesome sweet water for your whole family. Drink safe water and taste clean ice from Clatterans filters.
Fits The Following Series
45429 Series |
45433 Series |
58703 Series |
51103 Series |
51102 Series |
1.Press the eject button to release the filter from the base grille.
2.Pull the filter straight out.
3.Turn the cap counterclockwise to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
4.Align the ridge on the cap with the arrow on the new filter and turn the cap until it snaps into place.
NOTE: You can run the dispenser without a filter. Your water will not be filtered. Simply insert the cap all of the way into the base grille and rotate the cap until it is firmly in place.
5.Remove the protective covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
6.Push the filter into the base grille. The eject button will pop back out when the filter is fully engaged.
7.Run water from the dispenser for 5 minutes at .5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours
8.Reset the “replace filter” light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Carol On 2018-12-22 07:35:08
Thank you seem to be the correct one for my fridge. Perfect fit easy to install. Great tasting water. Price could be lower.
-
By Antonia On 2018-12-21 06:02:32
This is a good filter that does a pretty good job making our really crappy Akron water taste acceptable. Compatible with Whirlpool filter 3 perfectly. This is the second time I bought this filter and will buy it again.
-
By Eloise On 2018-12-19 05:54:10
I didn't want to spend the extra money on this higher end filter, but I thought I would give it a try. I must say the water does come out much cleaner and faster! After you instal the filter you are supposed to run it a few times before you can drink it. On my previous cheaper filter the water keeps coming out a bit cloudy until about the 6th time you run it. With this filter after the 2nd turn it was already looking clear, but because of using the other filter for so long I went ahead and ran it 5 times just incase. The water does taste cleaner and always looks clear. I feel better knowing that for a few more bucks I can get something safer for my family and myself. At least the drinking water is super clean!
-
By Christian On 2018-12-19 03:53:52
Good Product, last long. It's the whirlpool water filter for the fridges. Works well and we continue with the same ones. I think the prior manufacturer might've had a better taste but kinda impossible to get them now.
-
By Burgess On 2018-12-18 10:13:29
Works well, easy to install and a reasonable price. This is my third purchase of this filter 9030 and I'm quite happy with the product. I haven't noticed any bad smells or off flavors from the water passed through this filter although we have pretty good water quality here in the Pacific Northwest straight from the tap.
-
By Edgar On 2018-12-14 08:09:51
Great product. Installed easily! Will continue to buy when the filter needs to be replaced. Wish they weren't so pricey, but the water quality is amazing!
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.